d. 木地板施工时应保证相应的温度、湿度，施工完时应覆盖塑料薄膜，防止

d. 木地板施工时应保证相应的温度、湿度，施工完时应覆盖塑料薄膜，防止开裂和变形；
e. 地板铺贴后表面未处理前，应注意不能被有色油渍污染，不得将易磨划板面的砂子带入房间，不准在地面上拖压棱角尖锐的铁器重物；
f. 表面处理完毕后，须将门窗关闭，防止灰尘污染，并及时刷油和打蜡；
g. 通水和通暖时应注意节门及管道的三通弯头等处，防止渗漏后浸湿木地板，造成开裂及起鼓。
2. 水泥地面产品防护
a. 水泥砂浆地面产品防护：水泥砂浆面层施工完成后24小时内不准在上面行走或进行其它作业，以免碰坏地面，要适时做好养护工作；
b. 细石砼面层养护及产品防护：细石砼面层铺设24小时后，可用锯末或其它覆盖材料覆盖洒水湿润情况下硬化。养护期间，禁止上人走动或进行其它操作活动，以免损伤面层；
c. 水磨石地面产品防护：水磨石地面抛光后经常打蜡保护，使其地面显现光泽。
3. 楼梯的成品保护
对不抹灰预制楼梯和成品楼梯棱角处应有保护措施。
九. 木门窗安装保护
1. 一般木门框安装后应用铁皮保护，其保护高度应超过手推车轴，对于高级硬木框宜用1cm厚木板条钉设保护，防止砸碰门框，破坏剪裁口，影响安装和装修质量；
2. 修刨门窗时应用木楔将门边垫起卡牢，以免损坏门边，门窗扇进场后，应妥善管理，有条件的应入库，下面垫起离地20-30cm，码放整齐，上面盖好苫布，防止受潮；
3. 应对靠墙的木框，刷木材防腐剂进行处理，钢框刷好防潮漆，防止生锈；
4. 调整修理门窗时不得硬撬，以免损坏扇料和五金；
5. 安装工具应轻拿轻放，不得乱扔，以免损坏成品；
6. 安装门窗时严禁碰撞抹灰口角，防止损坏墙面抹灰层；
7. 已安好门扇、门窗应用木楔背紧，设专人看管，防止刮风时损坏；
8. 五金的安装应符合图纸要求，严禁丢漏；
9. 门扇安好后，不得在室内使用推车。
十. 钢门窗安产品防护
1. 钢门窗进场后应用布盖好，严防乱堆乱放，防止钢窗变形及生锈；
2. 钢门窗运输时要轻拿轻放，采取保护措施，避免摔压，磕碰，防止变形损坏；
3. 抹灰时残留在钢窗及钢门框扇上的砂浆应及时清理干净；
4. 脚手架严禁以钢门窗为固定点和架子的支点，禁止将架子拉、绑在钢门窗和窗扇上，防止钢门窗的位移和变形；
5. 拆架子时注意将开启的门窗关上后再落架子，防止撞坏钢窗。
十一. 铝合金门窗（塑钢）产品防护
1. 铝合金门窗应入库堆放，并将其垫起、垫平、码放整齐，防止变形。对已装好披水的铝合金门窗，注意存放时的支垫，防止破坏披水；
2. 门窗保护膜要封闭好，再进行安装，安装后及时将门框两侧用木板捆好，防止碰撞损坏；
3. 抹灰前应将铝合金门窗用塑料薄膜包扎或粘贴不干胶条进行保护，在门窗安装前以及室内外湿作业未完成以前，不得破坏保护膜，防止砂浆对其面层的侵蚀；
4. 铝合金门窗的保护膜应在交工前再撕去，要轻撕，且不可用铲刀铲,防止砂浆将其表面划伤，影响美观；
5. 如铝合金表面有胶状物时，应用棉丝蘸胶溶剂，擦拭干净，如发现局部划痕，用小毛刷蘸染液进行染补；
6. 架子搭设、室外抹灰、钢龙骨安装及管线施工运输过程，严禁蹭砸铝合金门窗边框。
十二. 玻璃安装保护
1. 凡已经安装门窗玻璃的建筑工程，必须派专人看管、维护。每日应按时开关门窗，尤其在风雨天更应注意；

ผลลัพธ์ (อังกฤษ) 1:

D. wooden floor construction shall ensure that the appropriate temperature, humidity, and finished construction should be covered with plastic film to prevent cracking and deformation;E. prior to the processing floor tile surface should be careful not to be colored oil pollution, sand from the surface on which it may not be easy to grind into the room, don't drag on the ground edges and sharp iron weights;F. surface treatment has been completed, doors and Windows shall be closed, to prevent dust pollution, and brush oil and wax;G. warm water and passes should note that section and pipeline links at the elbow, prevent leakage after wetting the wood floor, causing cracking and blistering.2. concrete product protectionA. cement mortar floor protection: cement mortar surface construction is completed within 24 hours are not allowed to walk on it or carry out other operations, so as not to hit the ground, doing maintenance work at the right time;B. conservation and preservation of fine stone concrete surface: fine-stone concrete surface about 24 hours later, sawdust or other covering materials covering sprinkler wet case hardening. Conservation period, the ban on people moving around or carrying out other operational activities, so as not to damage surface layer;C. terrazzo product protection: polishing of terrazzo floor often waxed to protect to make it appear shiny on the ground. 3. the stairs of finished product protectionFor not plastering prefabricated stairs and stair edges of finished products shall be protected.IX. the wooden door and window installation protection1. wooden door frame using metal protection after installation, its protective height should be more than a cart shaft, for advanced hardwood box should be treated with 1cm wood, nail protection to prevent hit touch the door frame, damaged trim, affect the quality of installation and decoration;2. application Windows and doors wooden door wedge pad planing cards, and so as to avoid damage to the door, Windows and doors fans after entering, should be properly managed, conditions should be put in storage, under 20-30cm, neatly, with cover sheet to prevent damp;3. against a wall of wooden frames, brush wood preservative treatment, steel box brush moisture-proof paint to prevent rust;4. adjust repaired Windows and doors may not be hard to pry, so as not to damage the fan and hardware;5. install the tools with care, not throw, so as not to damage the finished product;6. collision plastering angle is strictly prohibited when installing doors and Windows, and prevent damage to the wall plastering layer;7. safe doors, Windows and doors wooden wedge back tight, set up special guard to prevent wind damage;8. hardware installation should conform to the drawings, no lost leakage;9. after the doors are well, not for indoor use strollers.10. steel door and window protection 1. steel Windows and doors after entering cloth cover to prevent heap lying to prevent deformation of steel Windows and rusting; 2. the transport of steel doors and Windows when you're with care, protection, avoid falls, bumps to prevent damage; 3. when plaster residue in the steel Windows and mortar on steel door frame fan should be cleaned in a timely manner;4. scaffolds is prohibited with steel Windows and doors as a fixed point and the fulcrum of the shelf, shelf pull, is prohibited on the steel doors and window sash tied to prevent displacement and deformation of steel doors and Windows;5. Remove shelf will open up the doors and Windows closed when falling after shelf to prevent the damaged steel Windows.Eleven. Aluminum Windows and doors (plastic) product protection1. aluminum alloy doors and Windows should be put in storage stack, and mats, mats, it neatly and prevent distortion. Have installed aluminum Windows and doors of the shed, note when storing the pad to prevent destruction shed; 2. good protective film to close doors and Windows, and then install, after installation on both sides of the door frame with boards strapped to prevent collision damage; 3. aluminum alloy doors and Windows should be used before plastering plastic wrap or paste adhesive for protection, in front of the door and window installation, as well as indoor and outdoor humidity before the job was not completed, may destroy the protective film to prevent erosion of the surface layer of mortar; 4. aluminum alloy door and window protection film should be in place before then torn off, less tear and is not available with a spade a spade, prevents mortar from scratch on its surface is affected; 5. when the glue on the surface of aluminum alloy using cotton dipped in rubber solvent, wipe clean, if local scratch, using a small brush dipped in dye to dye up; 6. shelves installation, an outdoor plastering, steel joist installation and pipeline transport, do not hit the edge of aluminum alloy door and window borders.12. Glass installation protection 1. where building works have installed glazing, custody, maintenance, must be sent. Daily time switch Windows, rain day should pay particular attention;

ผลลัพธ์ (อังกฤษ) 2:

. should be wood floor construction to ensure appropriate temperature, humidity, construction should be finished plastic film cover to prevent cracking and deformation;
. E front surface of the rear floor tiling untreated, should be careful not to be contaminated colored oil, will not be easy to wear sand reticle plane into the room, not allowed to drag on the ground pressure of sharp edges and corners of the iron weights;
. F. after the completion of the surface treatment, shall doors and windows closed to prevent dust pollution, and timely brush oil and wax;
. G through and should pay attention to warm water through the three-way elbow section of the door and pipes, etc., to prevent leakage after wet wooden floor, causing cracking and the drum.
2. The concrete floor protection products
. A cement mortar flooring product protection: After the completion of the construction of cement mortar surface layer 24 within hours or are not allowed to walk on other operations, so as not to damage the ground, should be timely to do conservation work;
B. Fine Stone concrete surface maintenance and protection products: fine aggregate concrete surface laying 24 hours, available sawdust or other covering material covering the sprinkler under humid conditions hardening. During maintenance, walking or other prohibited Exalted operational activities, so as not to damage the surface layer;
C. Terrazzo floor product protection: protection terrazzo floor waxing often polished to make it appear shiny surface.
3. Stairs product protection
for not plastering prefabricated stairs and finished staircase edges and corners shall be protected.
Nine . Wood doors and windows installed protection
1. Usually wooden doorframe metal protection after installing the application, which should not exceed the height of the trolley shaft protection, hard wooden frame is appropriate for advanced 1cm thick planks nailed provided protection against smashing hit the door frame, destruction cutouts, affect the installation and decoration quality;
2. application of repair doors and windows when the plane door wedge paving the card firmly to avoid damaging the door, windows and doors after entering the fan should be properly managed, conditions should be put in storage, paving the ground below 20 - 30cm , neatly stacked, the top cover of the sheet to prevent moisture;
3. respond wall wooden frame, brush wood preservative treated steel frame brushed proof paint to prevent rust;
4. adjust pry repair doors and windows can not be hard to avoid fan material damage and hardware;
5. The installation tool should be gently, not to throw to avoid damage to the finished product;
6. No collision when installing windows and doors plaster mouth, to prevent damage to the wall plaster layer;
7. already well doors, application of wedge tight back doors and windows, set up special care to prevent damage when the wind blows;
8. Hardware installation shall comply with the requirements of the drawings, non-throwing leak;
9. after the door well, not use carts indoors.
Ten . Steel doors security product protection
1. steel doors after entering a cloth cover to prevent cluttered prevent deformation and rusting steel window;
2. When you want to transport steel doors gently, to take protective measures to avoid pressure drop, bump, prevent deformation damage;
3. plastering remaining on the steel window and door frames of steel fan mortar should be clean;
4. scaffolding non-steel windows and doors to a fixed pivot point and the shelf, pull the shelf prohibited, tied to the steel doors and sash to prevent displacement and deformation of steel doors and windows;
5. Note that will open the doors and windows shut and then off the shelf, to prevent crashing when the demolition steel window shelf.
Eleven . Aluminum doors and windows (PVC) product protection
1. Aluminum alloy doors and windows should be piled storage, and paving, flat pad, neatly stacked, to prevent deformation. Phi water have been installed aluminum doors and windows, note pad support during storage to prevent damage to Phi water;
2. doors and windows closed to protect the film is good, then install, after installation in a timely manner on both sides of the door frame with wooden planks strapped to prevent collisions damage;
3. plastering should be before the aluminum window dressing or paste adhesive strip protected by a plastic film, before the front doors and windows as well as indoor and outdoor wet work is not completed, may destroy the protective film to prevent mortar layer on its surface erosion;
4. the protective film of aluminum windows and doors should be torn off before the hand over, to tear the light, and not available shovel blade , to prevent mortar scratch its surface and affect appearance;
5. the aluminum alloy surface gum , the application of cotton yarn dipped in glue solvent, wipe clean, if found partial scratches were stained up with a small brush dipped in the dye;
6. rack erection, outdoor plastering, steel keel installation process pipeline construction and transportation, non-aluminum rub hit alloy doors and windows border.
Twelve . Glazing protection
1. Where the glass doors and windows have been installed building works must send someone to care and maintenance. Daily switch windows and doors should be, especially when the wind and rain days should pay attention;

ผลลัพธ์ (อังกฤษ) 3:

D. wood floor construction should ensure that the corresponding temperature, humidity, construction should cover plastic film, prevent cracking and deformation;E. floor after the post without surface treatment should be attention should not be colored oil stain pollution, may not be easily grinding stroke on the surface of the sand into the room, not on the ground drag sharp iron heavy pressure;F. after surface treatment, should be the closure of doors and windows, to prevent the dust pollution, and timely brush oil and wax;G. water and warm should pay attention to the valve and pipe three-way elbow, etc., prevent leakage after soaked wood floor, resulting in cracking and blistering.Two Protection of cement floor productsA. cement mortar ground product protection: cement mortar surface layer construction is not allowed to walk on the above or other operations within 24 hours, so as not to touch the ground, to timely do a good job conservation work;B. fine stone concrete surface maintenance and protection products: fine stone concrete surface layer is paved with 24 hours, available sawdust or other covering materials covered sprinkler wet hardening. During the curing period, prohibit people walk around or other operating activities, so as not to damage the surface layer;C. product protection: protection of terrazzo floor often waxing terrazzo floor after polishing, the surface appear luster.Three Finished product protectionThe prefabricated stairs stairs and plastering corners should take protective measures.Nine. Installation and protection of wooden doors and windowsOne General wooden box installed application tin protection, the protection height should be more than a cart shaft, for senior hardwood frame should be with 1cm thick lath nail design protection, prevent hit touch doorcase, destroy cut export of installation and decoration quality;Two Shaping doors and windows application wedge the door pad fastened, so as to avoid damage to the door, door and window fan after entering should be properly managed, conditions of storage, below the pad can more 20-30cm, stacked neatly, the above cover tarpaulin, to prevent damp.Three In response to the wooden frame by the wall, brush wood preservative for processing, steel frame brush good damp proof, prevent rust;Four Adjust the doors and windows of the repair shall not be hard to pry, so as not to damage the fan material and hardware;Five The installation tool should be handled with care, not littering, so as not to damage the product;Six The collision angle is prohibited to install windows and doors plastering wall plaster layer, prevent damage;Seven Have a built-in door and windows application wedge tight, with special care, prevent wind damage;Eight Hardware installation should meet the requirements of the drawings, is strictly prohibited to lose;Nine The door is installed, do not use the cart in the room.Ten. Steel door and window safety protection productsOne Steel doors and windows after entering the application cover, to prevent the cluttered, prevent the deformation and rust of steel window;Two Steel doors and windows transportation tohandlegentlyand, take protective measures to avoid the pressure drop, bump, prevent deformation damage;Three Plastering mortar in residual steel and steel frame of the fan should be clean;Four Scaffolding is strictly prohibited on steel doors and windows as the fulcrum of the fixed point and the shelves, prohibit the shelf pull, tied to the steel windows and doors and window sashes, prevent displacement and deformation of the steel doors and windows;Five Remove the shelves will open the doors and windows on the note after the fall shelf, prevent damaged windows.Eleven. Aluminum alloy doors and windows (Su Gang) product protectionOne Aluminum alloy doors and windows should be storage pile, and the pad, pad, neatly stacked, prevent deformation. To have installed water aluminum alloy doors and windows put, pay attention to deposit the support pad, to prevent the destruction of the phi water;Two Doors and windows to protect the film to be closed, and then the installation, the installation of the door on both sides of the timely use of wood tied to prevent damage to the collision;Three Plastering shall, prior to the aluminum alloy doors and windows with plastic film bandage or adhesive strip to protect, prior to installation of doors and windows and indoor and outdoor wet homework unfinished and shall not damage the protective film, prevent mortar on the surface layer of erosion;Four The protective film on the aluminum alloy doors and windows should be before commissioning and torn off, to light tear, and is not available to shovel shovel, prevent mortar will scratch the surface, affecting appearance.Five Such as aluminum alloy on the surface of jelly, application of cotton yarn dipping solvent, wipe clean, such as the discovery of local scratches, with a small brush dipped in dye to dye and fill;Six The shelf design, outdoor plastering, steel keel installation and construction of the pipeline transportation process, no hit Aluminum Alloy jamb rub.Twelve. Glass installation and protectionOne Where the installation of doors and windows glass construction projects, must send someone to look after, maintenance. Daily should be on time switch doors and windows, especially in the rainy day should pay attention to;